View FTLX3611M317_4772670.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Product Specification
RoHS-6 Compliant 10Gb/s DWDM 40km Multi-Rate XFP Optical Transceiver FTLX3611M3xx
PRODUCT FEATURES * * * * * * * * * * Supports 9.95Gb/s to 11.1Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 40km Temperature-stabilized DWDMrated EML transmitter RoHS-6 Compliant (lead-free) 100GHz ITU Grid, C Band Duplex LC connector Power dissipation <3.5W Built-in digital diagnostic functions Temperature range: -5C to 70C APPLICATIONS * * * * * * DWDM Networks SONET OC-192 IR-2 SDH STM S-64.2b OC-192/STM-64 with FEC 10GBASE-ER/EW 40km 10G Fibre Channel 10GBASE-ER/EW with FEC
Finisar's 40km FTLX3611M3xx Small Form Factor 10Gb/s (XFP) transceivers comply with the current XFP Multi-Source Agreement (MSA) Specification1. They comply with SONET OC-192 IR-2 and SDH STM S-64.2b, as well as with 10-Gigabit Ethernet 10GBASE-ER/EW per IEEE 802.3ae and 10-Gigabit Fibre Channel. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC3, and Finisar Application Note AN-20384.
PRODUCT SELECTION
FTLX3611M3xx
xx: 100GHz ITU Grid wavelength (see next page)
(c) Finisar Corporation 7-February-2008 Rev B2 Page 1
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
Center Wavelength (nm) 1563.86 1563.05 1562.23 1561.42 1560.61 1559.79 1558.98 1558.17 1557.36 1556.55 1555.75 1554.94 1554.13 1553.33 1552.52 1551.72 1550.92 1550.12 1549.32 1548.51 1547.72 1546.92 1546.12 1545.32 1544.53 1543.73 1542.94 1542.14 1541.35 1540.56 1539.77 1538.98 1538.19 1537.40 1536.61 1535.82 1535.04 1534.25 1533.47 1532.68 1531.90 1531.12 1530.33 1529.55 1528.77
Channel # 17* 18* 19* 20* 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60* 61*
Product Code FTLX3611M317 FTLX3611M318 FTLX3611M319 FTLX3611M320 FTLX3611M321 FTLX3611M322 FTLX3611M323 FTLX3611M324 FTLX3611M325 FTLX3611M326 FTLX3611M327 FTLX3611M328 FTLX3611M329 FTLX3611M330 FTLX3611M331 FTLX3611M332 FTLX3611M333 FTLX3611M334 FTLX3611M335 FTLX3611M336 FTLX3611M337 FTLX3611M338 FTLX3611M339 FTLX3611M340 FTLX3611M341 FTLX3611M342 FTLX3611M343 FTLX3611M344 FTLX3611M345 FTLX3611M346 FTLX3611M347 FTLX3611M348 FTLX3611M349 FTLX3611M350 FTLX3611M351 FTLX3611M352 FTLX3611M353 FTLX3611M354 FTLX3611M355 FTLX3611M356 FTLX3611M357 FTLX3611M358 FTLX3611M359 FTLX3611M360 FTLX3611M361
Frequency (THz) 191.7 191.8 191.9 192.0 192.1 192.2 192.3 192.4 192.5 192.6 192.7 192.8 192.9 193.0 193.1 193.2 193.3 193.4 193.5 193.6 193.7 193.8 193.9 194.0 194.1 194.2 194.3 194.4 194.5 194.6 194.7 194.8 194.9 195.0 195.1 195.2 195.3 195.4 195.5 195.6 195.7 195.8 195.9 196.0 196.1
*This channel is supported with limited availability -- Please contact Finisar for further details.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 2
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
I. Pin Descriptions
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Logic Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA Mod_Abs Mod_NR RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST Name/Description Module Ground Optional -5.2 Power Supply - Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply Module Ground Reference Clock non-inverted input, AC coupled on the host board - Not required Reference Clock inverted input, AC coupled on the host board - Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground Ref. 1
LVTTL-I LVTTL-O LVTTL-I
2
1
LVTTL-I LVTTLI/O LVTTL-O LVTTL-O LVTTL-O
2 2 2 2 2 1 1
CML-O CML-O
1
LVTTL-I
22 23 24 25 26 27 28 29 30
PECL-I PECL-I
VCC2 GND RefCLK+ RefCLKGND GND TDTD+ GND
1
1 1
CML-I CML-I
1
Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k - 10kohms on host board to a voltage between 3.15V and 3.6V.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 3
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
Diagram of Host Board Connector Block Pin Numbers and Names
II.
Absolute Maximum Ratings
Parameter Maximum Supply Voltage 1 Maximum Supply Voltage 2 Storage Temperature Case Operating Temperature
Symbol Vcc3 Vcc5 TS TOP
Min -0.5 -0.5 -40 -5
Typ
Max 4.0 6.0 85 70
Unit V V C C
Ref.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 4
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
III.
Electrical Characteristics (TOP = -5 to 70 C, VCC5 = 4.75 to 5.25 Volts)
Symbol Vcc5 Vcc3 Vcc2 Icc5 Icc3 Icc2 P Rin Vin,pp VD VEN Min 4.75 3.13 1.71 Typ Max 5.25 3.45 1.89 350 400 750 3.5 Unit V V V mA mA mA W mV V V us mV ps ps V V Ref.
Parameter Main Supply Voltage Supply Voltage #2 Supply Voltage #3 Supply Current - Vcc5 supply Supply Current - Vcc3 supply Supply Current - Vcc2 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Reference Clock Clock differential input impedance Reference Clock frequency Differential clock input swing Clock output rise/fall time Reference clock frequency tolerance
1 2 3
100 120 2.0 GND 820 Vcc GND+ 0.8 10 850 38 38 VccHOST GND+0.5 See Note 6 below 100 Baud/64 640 200 -100 1600 1250 +100 650
Vout,pp tr tf VLOS fault VLOS norm PSR Rclkin f0 Vclkin,pp trf Df
340
Vcc - 0.5 GND
4 5 5 6 6 7
MHz mV ps PPM
5
Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 - 80 % 6. Loss Of Signal is open collector to be pulled up with a 4.7k - 10kohm resistor to 3.15 - 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 5
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
IV.
Optical Characteristics (TOP = -5 to 70C, VCC5 = 4.75 to 5.25 Volts)
Please note that the Transmitter of the FTLX3611M3 becomes operational within 60 seconds of power-up. This is due to the time required for the EML to reach its optimum operating temperature.
Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Extinction Ratio Center Wavelength Spacing Transmitter Center Wavelength - End Of Life Transmitter Center Wavelength - Beginning Of Life Transmitter Dispersion Penalty (@ 800 ps/nm) Sidemode Supression ratio Tx Jitter Generation (peak-to-peak) Tx Jitter Generation (RMS) Relative Intensity Noise Receiver Receiver Sensitivity @ 9.95Gb/s to 11.1Gb/s Stressed Receiver Sensitivity (OMA) @ 11.1Gb/s Maximum Input Power Optical Center Wavelength Receiver Reflectance Path penalty at 40km LOS De-Assert LOS Assert LOS Hysteresis Symbol POUT ER c c TDP SSRmin Txj TxjRMS RIN RSENS1 RSENS2 PMAX C Rrx LOSD LOSA -1 1270 30 0.1 0.01 -130 -16 -11.3 Min -1 8.2 X-100 X-25 100 X X Typ Max +2 Unit dBm dB GHz pm pm dB dB UI UI dB/Hz dBm dBm dBm nm dB dB dBm dBm dB 6 7 Ref. 1 1 2 3 3
X+100 X+25 2
4 5
1600 -27 2 -22
8
-28 0.5
Notes: 1. Having ER=8.2dB guarantees that the -1 dBm minimum output power meets IEEE 802.3ae requirement of OMA = -2.4 dBm. 2. Corresponds to approximately 0.8 nm. 3. X = Specified ITU Grid wavelength. 4. Measured with a host jitter of 50 mUI peak-to-peak. 5. Measured with a host jitter of 7 mUI RMS. 6. Measured with worst ER; BER<10-12; PRBS31. Equivalent to -14.3 dBm OMA at ER = 8.2 dB. 7. Per IEEE 802.3ae. Equivalent to -14.3 dBm average power at Infinite ER. 8. Dispersion penalty is measured in loopback using 18 ps/(nm*km) fiber (SMF-28).
(c) Finisar Corporation 7-February-2008
Rev B2
Page 6
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
V.
General Specifications
Symbol BR BER LMAX Min 9.95 Typ Max 11.1 10-12 Units Gb/s km Ref. 1 2 1
Parameter Bit Rate Bit Error Ratio Max. Supported Link Length
40
Notes: 1. SONET OC-192 IR-2, 10GBASE-ER/EW, SONET OC-192 with FEC, 10GBASE-ER/EW with FEC 2. Tested with a 231 - 1 PRBS
VI.
Environmental Specifications
Finisar XFP transceivers have an operating temperature range from -5C to +70C case temperature.
Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -5 -40 Typ Max 70 85 Units C C Ref.
VII.
Regulatory Compliance
Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Laser Eye Safety Laser Eye Safety Electrical Safety Electrical Safety Agency FDA/CDRH TUV Standard CDRH 21 CFR 1040 and Laser Notice 50 EN 60825-1: 1994+A11:1996+A2:2001 IEC 60825-1: 1993+A1:1997+A2:2001 IEC 60825-2: 2000, Edition 2 EN 60950 CLASS 3862.07 CLASS 3862.87 Certificate Number 9210176-77 R72052602
TUV UL/CSA
R72052602 1439230
Copies of the referenced certificates are available at Finisar Corporation upon request.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 7
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
VIII. Digital Diagnostics Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: * * * * * Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information, including memory map definitions, please see the XFP MSA documentation1.
(c) Finisar Corporation 7-February-2008
Rev B2
Page 8
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
IX.
Mechanical Specifications
Finisar's XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA).
77.95
22.15
18.35
13.30 1.95
8.50
LATCHED
16.00 UNLATCHED 20.85 39.00 R1.00
XFP Transceiver (dimensions are in mm)
(c) Finisar Corporation 7-February-2008
Rev B2
Page 9
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
X.
PCB Layout and Bezel Recommendations
XFP Host Board Mechanical Layout (dimensions are in mm)
(c) Finisar Corporation 7-February-2008
Rev B2
Page 10
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
XFP Detail Host Board Mechanical Layout (dimensions are in mm)
(c) Finisar Corporation 7-February-2008
Rev B2
Page 11
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
XFP Recommended Bezel Design (dimensions are in mm)
(c) Finisar Corporation 7-February-2008
Rev B2
Page 12
FTLX3611M3 DWDM XFP Product Specification - February 2008
Finisar
XI. 1.
References 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 - August 2005. Documentation is currently available at http://www.xfpmsa.org/ Application Note AN-2035: "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers" - Finisar Corporation, December 2003 Directive 2002/95/EC of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". January 27, 2003. "Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers", Finisar Corporation, January 21, 2005.
2.
3.
4.
XII.
Revision History
Date 4/12/2006 4/21/2006 * * A1 * * A2 B B1 B2 5/22/2006 10/25/2006 9/28/2007 2/7/2008 * * * * * * Document created. Added OC-192/STM-64 with FEC in applications section Removed Finisar Confidential from footer. Replaced product photo. Updated BOL wavelength tolerance specification. Updated Finisar Address. Added Safety Certificate numbers. Document release. Updated note on channel. Added channel column. Description
Revision A
XII.
For More Information
Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com
(c) Finisar Corporation 7-February-2008
Rev B2
Page 13

▲Up To Search▲

Price & Availability of FTLX3611M317

	To Download FTLX3611M317 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .